MRF EezeeWood Interior Glossy 500ml

New

MRF EezeeWood is an economical, single pack polyurethane clear wood finish for interiors.

Other packs in this product

Eezeewood Inteior GlossyEezeewood Inteior Glossy
1 L200 mL

Also Available

Eezeewood XT MattEezeewood XT GlossyTouchwood Exterior MattTouchwood Interior Glossy
MRF Eezeewood Exterior MattMRF Eezeewood Exterior GlossyTouchwood Exterior MattTouchwood Glossy

More details

24 Items

By buying this product you can collect up to 16 loyalty points. Your cart will total 16 points that can be converted into a voucher of Rs. 0.80.


Rs. 160.00

Data sheet

MaterialFully reacted PU
FinishGloss
Non-YellowingYes
Scratch ResistantGood
Water ResistanceGood
Coverage90 - 100 Sqft / Ltr / Coat
ColourClear
ClarityGood
Recoating Time6 - 8 Hours
Method of ApplicationBrush, Roll , Spray
PackSingle Component

More info

MRF EezeeWood is an economical, single pack polyurethane clear wood finish for interior woods. MRF EezeeWood Exterior Matt gives a luxurious gloss finish to the wooden surface. It can be applied on interior wooden surfaces. It can be applied on surfaces that under go daily wear such as table tops and entrance doors. The coating provides long lasting protection to interior woods.

Features

  • Resistant to scratches
  • Water resistant
  • Easy to apply using a brush or roller

Application

Surface Preparation
  • The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination
  • For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220
  • For Veneer ply surfaces,start with Sandpaper #220
  • Always sand in the direction of the wood grain
Application Procedure
  • Mix the material thoroughly prior to application.
  • Avoid applying in direct sunlight or when the humidity is very high
  • Apply 2 to 3 coats of EEZEEWOOD XT / Interior Sealer clear with an interval of 12 - 16 hours between the subsequent coats. Sanding should be done prior to the application of each coat. Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats
  • The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood
  • Apply 2 coats of either EEZEEWOOD XT / Interior Glossy Clear or Matt Clear depending on the requirement, with an interval of 12 - 16 hours between the subsequent coats. Sanding of the 1st coat of top coat shall be done with #600 or #1000 Sandpaper
  • MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted
  • For Interior applications use Woodstains Interior shades only

Points to note

Use of inferior quality thinners and sealers/fillers should be avoided since it compromises the quality of the coating.

Technical Details

  • Thinner RecommendedThinner 3834
  • Drying and recoating Time : 6-8 hours
  • Coverage : 70 - 80 sqft per coat. Subsequent coats will have up to 15% higher coverage.
  • Finish : Transparent, Glossy

Reviews

Write a review

MRF EezeeWood Interior Glossy 500ml

MRF EezeeWood Interior Glossy 500ml

MRF EezeeWood is an economical, single pack polyurethane clear wood finish for interiors.

Other packs in this product

Eezeewood Inteior GlossyEezeewood Inteior Glossy
1 L200 mL

Also Available

Eezeewood XT MattEezeewood XT GlossyTouchwood Exterior MattTouchwood Interior Glossy
MRF Eezeewood Exterior MattMRF Eezeewood Exterior GlossyTouchwood Exterior MattTouchwood Glossy

Write a review

Accessories

30 other products in the same category: