Fosroc Reebaklens Multipurpose Cleaning Agent 1Ltr

Reebaklens is a multipurpose cleaning and etching agent in combination of acid based material, corrosion  inhibitors and dispersing agents and is supplied as a clear blue solution.

Uses

• Reebaklens is used for cleaning ceramic and glazed bathroom tiles, fittings and concrete floors
• Removal of mortar and plaster droppings on floor
• Fungus on wirecut bricks and clay tiles.
• Also for removal of hardened concrete from tools, implements and machinery, rust and mill scale from steelwork.
• Suitable for etching of concrete floors and surfaces prior to application surface coatings.

Benefits

• Rapid Action
• Non-Corrosive
• Penetrates oil and grease
• Used for cleaning ceramic & glazed tiles and brickwork
• Safe with metals (except zinc and galvanised steel), wood, glass and plastic.

Application Procedure

Cleaning brickwork

A small trial area should be cleaned fi rst to determine the most suitable Reebaklens cleaning agent dilution. Pre-wet the brickwork, then using a sponge, rub the affected areas with a solution of Reebaklens cleaning agent and water. Strength of the solution required will vary but should be between 1:1 and 1:4 (by volume of Reebaklens cleaning agent to water). When the action has finished, wash down thoroughly with clean water.

Cleaning large items of equipment

E.g. Readymix trucks, concrete mixers, barrows, etc. Reebaklens cleaning agent should be liberally applied to the deposits by a soft broom and allowed to soak overnight if possible. If the surfaces of the deposit can be cracked by mechanical means this will speed up the operation. In severe cases more than one application may be necessary. On completion, dissolved deposits and loose material should be wire brushed and washed away with clean water.

Cleaning small tools

Use Reebaklens as a dip. The tools should be soaked overnight, then taken out and washed with clean water to remove all loosely adhering materials. Care should be taken to avoid prolonged contact between Reebaklens and zinc or aluminium parts of tools, eg. rivets, etc.

Cleaning concrete floors

Pre-wet the floors, then using a stiff bristle broom, brush the affected areas with a solution of Reebaklens and water. Strength of the solution required will vary but should be between 1:1 and 1:4 ( Reebaklens cleaning agent to water). When the action has finished, wash down thoroughly with clean water.

Removal of rust and mill scale

Prewet the floors, then using a stiff bristle broom, brush the affected areas with a solution of Reebaklens and water. Strength of the solution required will vary but should be between 1 : 1 and 1 : 4 (Reebaklens to water). When the action has finished, wash down thoroughly with clean water. Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water. Repeat if necessary. High degree of rust or scale can be removed by soaking in the Reebaklens solution for 60 minutes.

Etching concrete floors

For etching surfaces to remove laitence and give a mechanical key before applying resin or other coating, Reebaklens cleaning agent should be diluted with water and applied at the rate of approximately 1 litre per 2 sq.m. The dilution will depend upon the condition of the fl oors and the degree of etching required, but normally it will be between 1:2 and 1:4. When the action has fi nished, wash down thoroughly with clean water.

Note: As treatment with Reebaklens can alter the surface finish of concrete, the minimum concentration necessary for effective removal of stains should be employed. The surface should be washed down with water immediately after the treatment is complete.

For rusted metal (iron base)

• Pre-wet the substrate, then brush the affected areas with a solution of reebaklens and water.
• Strength of the solution can be varied between 1:1 and 1:4 - reebaklens:water by volume as required.  
• When the action has finished, wash down thoroughly with clean water.

Health and Safety

• Reebaklens multipurpose cleaning agent is acid based and should be handled with care. It attacks zinc, aluminium and putty. If in doubt about its effect on a material, test a small area before application.
• Avoid contact with skin. Rubber gloves and goggles should be worn. 
• Wash spillages with plenty of water. 
• Enclosed areas should be well ventilated.   
• If contact with eyes occur, wash immediately with water and seek medical advice.

For more information, refer to the technical datasheet provided on this page.